ChemicalBook
Chinese Japanese Germany Korea

拳皇命运琢磨暴击:Anthracene

Anthracene
Anthracene structure
CAS No.
120-12-7
Chemical Name:
Anthracene
Synonyms
CI 10790;NSC 7958;ANTHRACIN;GREEN OIL;Anthracen;Antracene;ANTHRACENE;ANTHRAZENE;CI NO 10790;Anthraxcene
CBNumber:
CB7375466
Molecular Formula:
C14H10
Formula Weight:
178.23
MOL File:
120-12-7.mol

Anthracene Properties

Melting point:
215 °C
Boiling point:
340 °C(lit.)
Density 
1.28
vapor density 
6.15 (vs air)
vapor pressure 
1 mm Hg ( 145 °C)
refractive index 
1.5948
Flash point:
121 °C
storage temp. 
APPROX 4°C
solubility 
toluene: soluble20mg/mL, clear, colorless to faintly yellow
form 
powder
Colour Index 
10790
pka
>15 (Christensen et al., 1975)
color 
off-white to yellow
explosive limit
0.6%(V)
Water Solubility 
0.045 mg/L (25 ºC)
Merck 
14,682
BRN 
1905429
Henry's Law Constant
1.22 at 4 °C, 6.42 at 25 °C (dynamic equilibrium method, Bamford et al., 1999)
CAS DataBase Reference
120-12-7(CAS DataBase Reference)
NIST Chemistry Reference
Anthracene(120-12-7)
EPA Substance Registry System
Anthracene(120-12-7)
SAFETY
  • Risk and Safety Statements
  • Hazard and Precautionary Statements (GHS)
  • NFPA
Hazard Codes  Xi,N,F,T,Xn
Risk Statements  36/37/38-50/53-67-36-11-39/23/24/25-23/24/25-65-38-66-51/53
Safety Statements  26-60-61-24/25-16-9-45-36/37-62-36
RIDADR  UN 3077 9/PG 3
WGK Germany  2
RTECS  CA9350000
Autoignition Temperature 540 °C
TSCA  Yes
HazardClass  9
PackingGroup  III
HS Code  29029010
Hazardous Substances Data 120-12-7(Hazardous Substances Data)
Toxicity LD50 orally in Rabbit: > 16000 mg/kg
Symbol(GHS):
Signal word: Danger
Hazard statements:
Code Hazard statements Hazard class Category Signal word Pictogram P-Codes
H225 Highly Flammable liquid and vapour Flammable liquids Category 2 Danger P210,P233, P240, P241, P242, P243,P280, P303+ P361+P353, P370+P378,P403+P235, P501
H315 Causes skin irritation Skin corrosion/irritation Category 2 Warning P264, P280, P302+P352, P321,P332+P313, P362
H317 May cause an allergic skin reaction Sensitisation, Skin Category 1 Warning P261, P272, P280, P302+P352,P333+P313, P321, P363, P501
H319 Causes serious eye irritation Serious eye damage/eye irritation Category 2A Warning P264, P280, P305+P351+P338,P337+P313P
H335 May cause respiratory irritation Specific target organ toxicity, single exposure;Respiratory tract irritation Category 3 Warning
H336 May cause drowsiness or dizziness Specific target organ toxicity,single exposure; Narcotic effects Category 3 Warning P261, P271, P304+P340, P312,P403+P233, P405, P501
H351 Suspected of causing cancer Carcinogenicity Category 2 Warning P201, P202, P281, P308+P313, P405,P501
H370 Causes damage to organs Specific target organ toxicity, single exposure Category 1 Danger P260, P264, P270, P307+P311, P321,P405, P501
H400 Very toxic to aquatic life Hazardous to the aquatic environment, acute hazard Category 1 Warning P273, P391, P501
H410 Very toxic to aquatic life with long lasting effects Hazardous to the aquatic environment, long-term hazard Category 1 Warning P273, P391, P501
H411 Toxic to aquatic life with long lasting effects Hazardous to the aquatic environment, long-term hazard Category 2
Precautionary statements:
P201 Obtain special instructions before use.
P202 Do not handle until all safety precautions have been read and understood.
P210 Keep away from heat/sparks/open flames/hot surfaces. — No smoking.
P260 Do not breathe dust/fume/gas/mist/vapours/spray.
P261 Avoid breathing dust/fume/gas/mist/vapours/spray.
P264 Wash hands thoroughly after handling.
P264 Wash skin thouroughly after handling.
P271 Use only outdoors or in a well-ventilated area.
P272 Contaminated work clothing should not be allowed out of the workplace.
P273 Avoid release to the environment.
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P311 Call a POISON CENTER or doctor/physician.
P321 Specific treatment (see … on this label).
P391 Collect spillage. Hazardous to the aquatic environment
P301+P310 IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician.
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continuerinsing.
P308+P313 IF exposed or concerned: Get medical advice/attention.
P333+P313 IF SKIN irritation or rash occurs: Get medical advice/attention.
P337+P313 IF eye irritation persists: Get medical advice/attention.
P405 Store locked up.
P403+P233 Store in a well-ventilated place. Keep container tightly closed.
P501 Dispose of contents/container to..…

NFPA 704

Diamond Hazard Value Description
1
Health  
Flammability   1 Materials that require considerable preheating, under all ambient temperature conditions, before ignition and combustion can occur. Includes some finely divided suspended solids that do not require heating before ignition can occur. Flash point at or above 93.3 °C (200 °F). (e.g. mineral oil, ammonia)
Instability  
Special  

拳皇命运图片高清大全 www.ljntc.icu (NFPA, 2010)

Anthracene price More Price(28)

Manufacturer Product number Product description CAS number Packaging Price Updated Buy
Sigma-Aldrich 10580 Anthracene suitable for scintillation, ≥99.0% (GC) 120-12-7 25g $72.3 2018-11-13 Buy
Sigma-Aldrich 07671 Anthracene certified reference material, TraceCERT 120-12-7 100mg $91.6 2018-11-13 Buy
TCI Chemical A0405 Anthracene Zone Refined (number of passes:30) >99.5%(GC) 120-12-7 1sample $101 2018-11-22 Buy
TCI Chemical A0495 Anthracene >97.0%(GC) 120-12-7 25g $26 2018-11-22 Buy
Alfa Aesar 032320 Anthracene, 90+% 120-12-7 500g $39 2018-11-16 Buy

Anthracene Chemical Properties,Uses,Production

Chemical Properties

Anthracene is colorless, to pale yellow crystalline solid with a bluish fluorescence. PAHs are compounds containing multiple benzene rings and are also called polynuclear aromatic hydrocarbons.

Physical properties

White to yellow crystalline flakes or crystals with a bluish or violet fluorescence and a weak aromatic odor. Impurities (naphthacene, tetracene) impart a yellowish color with green fluorescence.

Uses

Anthracene has been shown to be soluble in a variety of binary and ternary mixtures of cyclohexanone, ethyl acetate, and methanol 1,2.

Uses

Anthracene is an aromatic hydrocarbonwith three fused rings, and is obtained by the distillationof crude oils. The main useis in the manufacture of dyes.It is an important source of dyestuffs.

Definition

(C14H10) A white crystalline solid used extensively in the manufacture of dyes. Anthracene is found in the heavy- and green-oil fractions of crude oil and is obtained by fractional crystallization. Its structure is benzene-like, having three six-membered rings fused toanion gether. The reactions are characteristic of AROMATIC COMPOUNDS.

General Description

White to yellow solid with a weak aromatic odor. Sinks in water.

Air & Water Reactions

Flammable. Insoluble in water.

Reactivity Profile

Anthracene will spontaneously burst into flame on contact with chromic acid, and other strong oxidants.

Hazard

A questionable carcinogen.

Health Hazard

Carcinogenicity of anthracene is not known.Its toxicity is very low. An intraperitonealLD50 in mice is recorded at 430 mg/kg(NIOSH 1986).

Health Hazard

Inhalation of dust irritates nose and throat. Contact with eyes causes irritation.

Fire Hazard

Anthracene is combustible.

Safety Profile

Moderately toxic by intraperitoneal route. A skin irritant and allergen. Questionable carcinogen with experimental neoplas tigenic and tumorigenic data. Mutation data reported. Combustible when exposed to heat, flame, or oxidizing materials. Moderately explosive when exposed to flame, Ca(OCl)z, chromic acid. To fight fire, use water, foam, CO2, water spray or mist, dry chemical. Explodes on contact with fluorine.

Potential Exposure

It is used as an intermediate in dye stuffs (alizarin), insecticides, and wood preservatives; making synthetic fibers, anthraquinone, and other chemicals. May be present in coke oven emissions, diesel fuel, and coal tar pitch volitiles.

Source

Concentrations in 8 diesel fuels ranged from 0.026 to 40 mg/L with a mean value of 6.275 mg/L (Westerholm and Li, 1994). Lee et al. (1992) reported concentration ranges of 100– 300 mg/L and 0.04–2 μg/L in diesel fuel and corresponding aqueous phase (distilled water), respectively. Schauer et al. (1999) reported anthracene in diesel fuel at a concentration of 5 μg/g and in a diesel-powered medium-duty truck exhaust at an emission rate of 12.5 μg/km. Anthracene was detected in a distilled water-soluble fraction of used motor oil at concentrations ranging from 1.1 to 1.3 μg/L (Chen et al., 1994).
California Phase II reformulated gasoline contained anthracene at a concentration of 4.35 μg/kg. Gas-phase tailpipe emission rates from gasoline-powered automobiles with and without catalytic converters were 3.69 and 148 μg/km, respectively (Schauer et al., 2002).
Thomas and Delfino (1991) equilibrated contaminant-free groundwater collected from Gainesville, FL with individual fractions of three individual petroleum products at 24–25 °C for 24 h. The aqueous phase was analyzed for organic compounds via U.S. EPA approved test method 625. Average anthracene concentrations reported in water-soluble fractions of kerosene and diesel fuel were 12 and 25 μg/L, respectively. Anthracene was ND in the water-soluble fraction of unleaded gasoline.
The concentration of anthracene in coal tar and the maximum concentration reported in groundwater at a mid-Atlantic coal tar site were 5,000 and 0.02 mg/L, respectively (Mackay and Gschwend, 2001). Based on laboratory analysis of 7 coal tar samples, anthracene concentrations ranged from 400 to 8,600 ppm (EPRI, 1990). A high-temperature coal tar contained anthracene at an average concentration of 0.75 wt % (McNeil, 1983). Lehmann et al. (1984) reported an anthracene concentration of 34.8 mg/g in a commercial anthracene oil.
Nine commercially available creosote samples contained anthracene at concentrations ranging from 5,500 to 14,000 mg/kg (Kohler et al., 2000).
Anthracene was detected in asphalt fumes at an average concentration of 45.89 ng/m3 (Wang et al., 2001).
Schauer et al. (2001) measured organic compound emission rates for volatile organic compounds, gas-phase semi-volatile organic compounds, and particle-phase organic compounds from the residential (fireplace) combustion of pine, oak, and eucalyptus. The respective gas-phase and particle-phase emission rates of anthracene were 3.44 and 0.228 mg/kg of pine burned, 2.13 and 0.0230 mg/kg of oak burned, and 1.76 and 0.0061 mg/kg of eucalyptus burned.
Under atmospheric conditions, a low rank coal (0.5–1 mm particle size) from Spain was burned in a fluidized bed reactor at seven different temperatures (50 °C increments) beginning at 650 °C. The combustion experiment was also conducted at different amounts of excess oxygen (5 to 40%) and different flow rates (700 to 1,100 L/h). At 20% excess oxygen and a flow rate of 860 L/h, the amount of anthracene emitted ranged from 558.7 ng/kg at 900 °C to 2,449.7 ng/kg at 800 °C. The greatest amount of PAHs emitted were observed at 750 °C (Mastral et al., 1999).

Environmental Fate

Biological. Catechol is the central metabolite in the bacterial degradation of anthracene. Intermediate by-products included 3-hydroxy-2-naphthoic acid and salicylic acid (Chapman, 1972). Anthracene was statically incubated in the dark at 25 °C with yeast extract and settled domestic wastewater inoculum. Significant biodegradation with gradual adaptation was observed. At concentrations of 5 and 10 mg/L, biodegradation yields at the end of 4 wk of incubation were 92 and 51%, respectively (Tabak et al., 1981). A mixed bacterial community isolated from seawater foam degraded anthraquinone, a photodegradation product of anthracene, to traces of benzoic and phthalic acids (Rontani et al., 1975). In activated sludge, only 0.3% mineralized to carbon dioxide after 5 d (Freitag et al., 1985).
Soil. In a 14-d experiment, [14C]anthracene applied to soil-water suspensions under aerobic and anaerobic conditions gave 14CO2 yields of 1.3 and 1.8%, respectively (Scheunert et al., 1987). The reported half-lives for anthracene in a Kidman sandy loam and McLaurin sandy loam are 134 and 50 d, respectively (Park et al., 1990).
Surface Water. The removal half-lives for anthracene in a water column at 25 °C in midsummer sunlight were 10.5 h for deep, slow, slightly turbid water; 21.6 h for deep, slow, muddy water; 8.5 h deep, slow, clear water; 3.5 h for shallow, fast, clear water, and 1.4 h for very shallow, fast, clear water (Southworth, 1977).
Photolytic. Oxidation of anthracene adsorbed on silica gel or alumina by oxygen in the presence of UV-light yielded anthraquinone. This compound additionally oxidized to 1,4-dihydroxy- 9,10-anthraquinone. Anthraquinone also formed by the oxidation of anthracene in diluted nitric acid or nitrogen oxides (quoted, Nikolaou et al., 1984) and in the dark when adsorbed on fly ash (Korfmacher et al., 1980). Irradiation of anthracene (2.6 mM) in cyclohexanone solutions gave 9,10-anthraquinone as the principal product (Korfmacher et al., 1980). Photocatalysis of anthracene and sulfur dioxide at -25 °C in various solvents yielded anthracene-9-sulfonic acid (Nielsen et al., 1983). Schwarz and Wasik (1976) reported a fluorescence quantum yield of 0.25 for anthracene in water.
Chemical/Physical. In urban air from St. Louis, MO, anthracene reacted with NOx forming 9- nitroanthracene (Ramdahl et al., 1982).

Shipping

UN2811 Toxic solids, organic, n.o.s., Hazard Class: 6.1; Labels: 6.1-Poisonous materials, Technical Name Required.

Purification Methods

Likely impurities are anthraquinone, anthrone, carbazole, fluorene, 9,10-dihydroanthracene, tetracene and bianthryl. Carbazole is removed by continuous-adsorption chromatography [see Sangster & Irvine J Phys Chem 24 670 1956] using a neutral alumina column and eluting with n-hexane. [Sherwood in Purification of Inorganic and Organic Materials, Zief (ed), Marcel Dekker, New York, 1969.] The solvent is evaporated, and anthracene is sublimed under vacuum, then purified by zone refining, under N2 in darkness or non-actinic light. It has also been purified by co-distillation with ethylene glycol (boils at 197.5o), from which it can be recovered by addition of water, followed by crystallisation from 95% EtOH, *benzene, toluene, a mixture of *benzene/xylene (4:1), or Et2O. It has also been chromatographed on alumina with pet ether in a dark room (to avoid photo-oxidation of adsorbed anthracene to anthraquinone). Other purification methods include sublimation in a N2 atmosphere (in some cases after refluxing with sodium), and recrystallisation from toluene [Gorman et al. J Am Chem Soc 107 4404 1985]. Anthracene has been crystallised from EtOH, chromatographed through alumina in hot *benzene (fume hood) and then sublimed in a vacuum in a pyrex tube that has been cleaned and baked at 100o. (For further details see Craig & Rajikan J Chem Soc, Faraday Trans 1 74 292 1978, and Williams & Zboinski J Chem Soc, Faraday Trans 1 74 611 1978.) It has been chromatographed on alumina, recrystallised from n-hexane and sublimed under reduced pressure. [Saltiel J Am Chem Soc 108 2674 1986, Masnori et al. J Am Chem Soc 108 1126 1986.] Alternatively, recrystallise it from cyclohexane, chromatograph it on alumina with n-hexane as eluent, and recrystallise two more times [Saltiel et al. J Am Chem Soc 109 1209 1987]. Anthracene is fluorescent and forms a picrate complex, m 139o, on mixing the components in CHCl3 or *C6H6, but decomposes on attempted crystallization. [Beilstein 5 IV 228.]

Incompatibilities

Finely dispersed powder may form explosive mixture in air. Contact with strong oxidizers (chlorates, nitrates, peroxides, permanganates, perchlorates, chlorine, bromine, fluorine, etc.); contact may cause fires or explosions. Keep away from alkaline materials, strong bases, strong acids, oxoacids, epoxides, chromic acid/or calcium hypochlorite.

Waste Disposal

Consult with environmental regulatory agencies for guidance on acceptable disposal practices. Generators of waste containing this contaminant (≥100 kg/mo) must conform with EPA regulations governing storage, transportation, treatment, and waste disposal. Incineration.

Anthracene Preparation Products And Raw materials

Raw materials

Preparation Products


Anthracene Suppliers

Global( 235)Suppliers
Supplier Tel Fax Email Country ProdList Advantage
Capot Chemical Co.,Ltd.
+86 (0)571-855 867 18
+86 (0)571-858 647 95 [email protected] China 19917 60
Shanghai Time Chemicals CO., Ltd.
+86-021-57951555
+86-021-57951555 [email protected] CHINA 1365 55
Mainchem Co., Ltd.
+86-0592-6210733
+86-0592-6210733 [email protected] CHINA 32447 55
Xiamen AmoyChem Co., Ltd
+86 (0)592-605 1114
[email protected] CHINA 6370 58
career henan chemical co
+86-371-86658258
[email protected] CHINA 25791 58
Chemwill Asia Co.,Ltd.
86-21-51086038
86-21-51861608 [email protected];[email protected];[email protected];[email protected] CHINA 23954 58
Hubei Jusheng Technology Co.,Ltd.
8615527864001
[email protected] CHINA 28237 58
Haihang Industry Co.,Ltd
86-531-88032799
+86 531 8582 1093 [email protected] CHINA 8263 58
Hubei xin bonus chemical co. LTD
8613657299721
[email protected] CHINA 23049 58
Shijiazhuang XinZhaoYang Chemical Technology Co., Ltd. 0311-69032540 13931172911
0311-69032540 [email protected] China 292 55

View Lastest Price from Anthracene manufacturers

Image Release date Product Price Min. Order Purity Supply Ability Manufacturer
2018-08-13 Anthracene
120-12-7
US $1.00 / KG 1KG 98% 1ton career henan chemical co

Anthracene Spectrum


120-12-7(Anthracene)Related Search:


Copyright 2017 ? ChemicalBook. All rights reserved